Call now

GE Washer Error 26 and 23: Not Spinning, Clothes Wet (Beverly Hills Repair)

GE washer fault 26 with clothes left wet usually means worn suspension rods. A real Beverly Hills repair on a GE laundry center: diagnosis, fix and $395 cost.

Quick answer: on a GE top-load washer or GE laundry center, fault 26 means the washer could not reach its final spin speed because the load was out of balance. If the clothes come out wet and the tub bangs or wobbles during spin even with a normal load, the most common cause is worn suspension rods. Fault 23 (lid lock) often shows up at the same time, but on this job the lid lock itself was fine.

The job: GE laundry center in Beverly Hills

The client called because the washer on their GE stacked laundry center, model GUD27GSSM2WW, was not working right. Loads were finishing wet and the machine was not spinning out.

I put the washer into service test mode and read the stored faults. It showed two codes: 26 and 23.

How I read the fault codes: GE washer service test mode

On this GE laundry center (dial controls with status lights, no digital display), the stored faults are read in service test mode:

  1. Turn the cycle selector to Off.
  2. Press and hold Start, and while holding it, turn the selector clockwise 6 clicks, from Off to Whites Heavy.
  3. Release Start. The washer enters test mode.
  4. Turn the selector one click to Whites Medium and wait until the Lid Locked light comes on.
  5. Press Start to show the first stored fault. Press Start again to show the next one.

Without a display, the fault number is shown in binary with the five status lights. Each light has a value: On = 16, Wash = 8, Rinse = 4, Spin = 2, Lid Locked = 1. Add up the lit lights to get the fault number:

  • Fault 26 = On + Wash + Spin (16 + 8 + 2).
  • Fault 23 = On + Rinse + Spin + Lid Locked (16 + 4 + 2 + 1).

The service sheet for your model is usually tucked behind the control panel or under the top. Follow it for your exact washer, since steps can differ between models.

What GE fault 26 and fault 23 mean

  • Fault 26, out of balance (OOB) ended final spin: the washer tried to redistribute the load but could not get rid of the out-of-balance condition, so it never reached the target spin speed. GE’s service sheet lists the balance ring, the suspension rod and spring assemblies and the speed sensor as the parts to check.
  • Fault 23, critical lid lock failure: the control saw a lid lock problem, such as the lock being blocked or not locking and unlocking.

On this machine the lid lock latched and released normally every time, so I did not replace it. The heavy shaking during spin was the real problem, and the lid lock code was a side effect of it.

Why worn suspension rods stop the spin

In a top-load washer the tub hangs on four suspension rods with springs and dampers. Over time the springs and dampers wear out. Then, as spin speed rises, the tub starts swinging hard. The control reads that as an out-of-balance load, slows down, tries to rebalance, and finally gives up before full spin. The result is wet clothes and, often, a fault 26.

The repair and the cost

I replaced all four suspension rods as a set, so the tub hangs evenly again. After the repair the tub stays steady through spin and the washer spins the load out normally.

Total for this repair: $395. The repair is covered by our 90-day warranty on parts and labor.

Tip: do not overload the washer

Overloading is one of the main reasons suspension rods wear out early. A packed tub throws the load off balance on every spin and puts extra stress on the springs and dampers. It is better to put in less than too much. If you have a lot of laundry, split it into two loads. A smaller load washes cleaner and spins drier.

When to call a technician

  • Clothes come out wet even after a Drain & Spin cycle.
  • The tub bangs, wobbles or walks the machine during spin with a normal load.
  • The washer shows fault 26, 22 or 31 (out-of-balance codes) again and again.

Before you replace a lid lock or a control board because of a fault code, have the suspension checked. It is often the cheaper fix.

Related: GE washer error code 3 (locked rotor) and washer repair in West Hollywood.

Vertex Appliance Repair serves West Hollywood, Beverly Hills, Hollywood and nearby neighborhoods. $89 diagnostic, waived when you proceed with the repair. 90-day warranty on parts and labor. Call (323) 747-7098.

Vertex Appliance Repair on: Google · Yelp · Thumbtack · BBB · Facebook